Picture checks

A picture check is used to store image bitmaps, known as baseline pictures, which can be compared during testing against bitmaps produced by the AUT.

When your test needs to check a control or property for the presence of an expected text or numeric value, it’s simple enough to enter that value into the appropriate action line, such as done here for the expected argument:

                           window      control    property  expected
check control property     car login   btn_login  caption   Login 

Sometimes, however, rather than checking for the presence of character-based content, you may want to make sure that an AUT window or control is displaying an expected picture, or bitmap. To accomplish such tasks, TestArchitect offers a suite of picture handling actions.

Unfortunately, you can’t just insert an expected bitmap directly into a picture handling action line. Instead, you have to pre-store the expected picture, known as the baseline picture, in a special item dedicated to that purpose. That item is a picture check. And a picture handling action, such as does picture exist, can test the validity of a bitmap displayed by the AUT simply by pointing to the appropriate picture check against which it is to be compared.

Baseline Picture

You may save a captured image and designate it as a baseline. All future captured images are then compared against this baseline image. Image comparison is considered to be successful only if the compared image and the baseline image are identical.

Sometimes, comparison may fail even if the content of the compared images seem to be identical. Various factors may cause these image comparison failures. For example, if, during testing, a given image file is rendered on display hardware with a different resolution than that which was used for the capture of the baseline image, it is quite possible for the comparison to fail. To improve the reliability of picture check comparisons, one picture check can store multiple baseline images. When, during testing, multiple baselines exist for a given picture check, a match between the just-captured image and any oneof the associated baselines is sufficient for the check to be considered as passed.

Keeping Picture Checks

There are two ways in which TestArchitect stores the picture checks:

Definition of regular picture checks

As a tester, you would use regular picture checks for pictures like charts (histograms, graphs, pie charts, etc.), that need to accurately display data that is specific for the situation where the check picture built-in action is applied.

Note:

Definition of shared picture checks

Shared picture checks are useful for standard pictures, like symbols and icons, where as a tester you mainly want to know if the correct picture is displayed by an application, but not what that picture exactly looks like. For example, the TestArchitect explorer tree has a special icon designating a test module, which varies slightly depending on whether the given item is checked in, checked out to you, or checked out to someone else. A test may need to verify only that a given icon being displayed is a test module icon, without regard to its particular state-dependent appearance. The example discussed above, with the picture of the Chevrolet Monte Carlo, would also work best as a shared picture check if, say, future versions of the application may update their car pictures.

Note:

Suppose that we use a check picture action with a name argument of /chevy in a test module. After running that test module, we approve the picture as a baseline. We can then see the picture check and the stored baseline picture in the TestArchitect explorer tree, as shown below. By double-clicking the Baseline node, we can view that baseline picture.

Capturing new picture checks, or adding baseline images to a picture check

There are essentially three ways to accomplish this:

Picture Capturing tool
The Picture Capturing tool lets you instantly capture the screen images of your test machines.

Key Points Modification tool
The Key Points Modification tool applies a keypoint detection technique to detect matched objects between baseline images and a target images.

Importing external image sources
TestArchitect lets you easily import image files (.PNG) format) as a new picture checks or additional new baseline images.

Exporting baseline images
Baseline images can be exported to image files (.PNG format), which can be used as a backup or for re-importing.

Resolving unverified picture checks
Explains step-by-steps procedures to resolve unverified picture checks.

Configuring notification time period to resolve unverified picture checks
By default, you will be notified every five days when you log into a repository which has repository test results containing unverified picture checks.


Copyright © 2021 LogiGear Corporation. All rights reserved. LogiGear is a registered trademark, and Action Based Testing and TestArchitect are trademarks of LogiGear Corporation. All other trademarks contained herein are the property of their respective owners.

LogiGear Corporation

1730 S. Amphlett Blvd. Suite 200, San Mateo, CA 94402

Tel: +1(800) 322-0333